Blogs RSS Blogs RSS Forums RSS Forums RSS
•
•
•
•
Showing results 1 to 40 of 402
Search took 0.03 seconds. Posts Made By: fren
Save these search results for 24 hours
Page 1 of 11 1 2 > Last »
Forum: Troubleshooting Dead Machines Oct 16th, 2007
Replies: 15
Views: 961
Posted By fren
Re: New Mobo and cpu, now no go.

Have you tried to turn it on directly through the power switch pin terminal from the motherboard?
Forum: Troubleshooting Dead Machines Oct 12th, 2007
Replies: 8
Views: 3,439
Posted By fren
Re: 1720-SMART detetcts imminent failure (Fail Attr:02)

I think your drive is going to fail. Try to do a clean install and check if you can do it successfully. If not, replace your hard drive.
Forum: Troubleshooting Dead Machines Oct 12th, 2007
Replies: 2
Views: 432
Posted By fren
Re: Big Problem... PLEASE HELP

Reseat your ram sticks or run your computer with a single stick, check what will happen. Also try it in different slots.
Forum: Troubleshooting Dead Machines Oct 12th, 2007
Replies: 9
Views: 1,065
Posted By fren
Re: Turns on but no boot

Try this first:

Unplug the AC adapter from your computer.

Remove the main battery.

Remove the memory sticks in their slots and clean their gold contact with a pencil eraser.

Keep pressing the...
Forum: Troubleshooting Dead Machines Oct 12th, 2007
Replies: 4
Views: 554
Posted By fren
Re: machine restarts when u open an exe. application

Your system might be infected with viruses or malwares. Since you won't be able to run any executable files. I advise you to update your antivirus definition lists and to scan your system.

If you...
Forum: Cases, Fans and Power Supplies Oct 11th, 2007
Replies: 21
Views: 1,741
Posted By fren
Re: Power supply maybe?

Remove your ram stick and pull the cmos battery out on the motherboard for about 10 mins. Put everything back in again.
Forum: Cases, Fans and Power Supplies Oct 11th, 2007
Replies: 21
Views: 1,741
Posted By fren
Re: Power supply maybe?

Have you tried to set your bios in default settings?
Forum: Cases, Fans and Power Supplies Oct 11th, 2007
Replies: 5
Views: 701
Posted By fren
Re: Power on & off all on it's own

If you use a single memory stick in your system , what will happen? Use one stick at a time and try to test it also in different slots.
Forum: Cases, Fans and Power Supplies Oct 11th, 2007
Replies: 21
Views: 1,741
Posted By fren
Re: Power supply maybe?

With one memory stick installed, what will happen? Use one stick at a time and try to test it also in different slots.
Forum: Troubleshooting Dead Machines Oct 11th, 2007
Replies: 6
Views: 2,465
Posted By fren
Re: Dell Inspiron 2600 Notebook RAM/Mainboard trouble

If those two sticks installed in your computer came with the original factory setup and they were successfully working together previously. I think what you need to do is set the bios again in...
Forum: Troubleshooting Dead Machines Oct 10th, 2007
Replies: 4
Views: 583
Posted By fren
Re: Blue screen

Perform xp repair install.
Forum: Troubleshooting Dead Machines Oct 10th, 2007
Replies: 6
Views: 2,109
Posted By fren
Re: Kernel Data Inpage Error, Portege 7000ct

Have you tried to work with your memory modules? Try that too.
Forum: Troubleshooting Dead Machines Oct 10th, 2007
Replies: 3
Views: 1,717
Posted By fren
Re: HP ZD8000 - Wont turn on

Unplug the AC adapter from your computer.

Remove the main battery.

Remove the memory sticks in their slots and clean their gold contact with a pencil eraser.

Keep pressing the power button for...
Forum: Troubleshooting Dead Machines Oct 10th, 2007
Replies: 6
Views: 2,465
Posted By fren
Re: Dell Inspiron 2600 Notebook RAM/Mainboard trouble

It's a memory issue.

Clean the gold contact of the sticks and reseat them several times in their slots.

Or the last memory upgrade might not be compatible with your system.
Forum: Troubleshooting Dead Machines Oct 9th, 2007
Replies: 9
Views: 12,672
Posted By fren
Re: PXE-E61 Media Test Failure

Okay reset the bios in default values then start your computer.

If it doesn't work, it's time to work with your hard drive.

Try to pull your hard drive out in its bay and put it back again (bad...
Forum: Cases, Fans and Power Supplies Oct 8th, 2007
Replies: 1
Views: 530
Posted By fren
Re: Burnt laptop connection - what to do?

Check the output voltage of your power adapter or try it with another power adapter. Sometimes the problem was caused by a faulty or shorted power adapter.
Forum: Windows NT / 2000 / XP / 2003 Oct 8th, 2007
Replies: 18
Views: 2,805
Posted By fren
Re: CD-RW and DVD-RW is not detected in My Computer

Do your drives detect in the bios? Did you flash your bios before?
Forum: Windows NT / 2000 / XP / 2003 Oct 8th, 2007
Replies: 3
Views: 473
Posted By fren
Re: plz resolve it

Maybe your computer was attacked by malwares or trojans or viruses. What you'll need to do is install a firewall aside from your antivirus program to prevent or to protect your system from any...
Forum: Windows NT / 2000 / XP / 2003 Oct 8th, 2007
Replies: 3
Views: 473
Posted By fren
Re: plz resolve it

Download and execute to get rid of the issue:

http://www.techsupportforum.com/sectools/sUBs/Flash_Disinfector.exe
Forum: Troubleshooting Dead Machines Oct 8th, 2007
Replies: 3
Views: 546
Posted By fren
Re: booting problem

Reinstall or repair your operating system. Check if this helps.
Forum: Troubleshooting Dead Machines Oct 7th, 2007
Replies: 3
Views: 4,918
Posted By fren
Re: 3 long beeps with my Elitegroup ECS Green 320 laptop

We were not sure if the card installed by a technician was also compatible with your computer unless you bought it in a memory card manufacturer (Crucial site).

The last resort I can see is clean...
Forum: Troubleshooting Dead Machines Oct 6th, 2007
Replies: 3
Views: 4,918
Posted By fren
Re: 3 long beeps with my Elitegroup ECS Green 320 laptop

It refers to your base memory, either the ram stick or your dimm slot is malfunctioning. Try to put your memory module in into another slot then boot up your computer. If it still doesn't work, try...
Forum: Troubleshooting Dead Machines Oct 6th, 2007
Replies: 9
Views: 12,672
Posted By fren
Re: PXE-E61 Media Test Failure

Maybe it's a hard disk or software (OS) problem. Try to reinstall or repair your operating system.
Forum: Storage Oct 6th, 2007
Replies: 3
Views: 1,932
Posted By fren
Re: New Biostar motherboard, please help

See to it that your dvd/cdroms are recognized by the bios. Have you checked the jumper settings of your cdroms? Try to check in the bios if the ide controllers (primary and secondary controllers) are...
Forum: Troubleshooting Dead Machines Oct 6th, 2007
Replies: 5
Views: 1,168
Posted By fren
Re: Cannot install any OS.

I think it was a hardware problem. Make sure the bios detects the hard drive.
Forum: Troubleshooting Dead Machines Oct 6th, 2007
Replies: 18
Views: 2,030
Posted By fren
Re: Pc doesnt start up

hmmm if you feel that it was not the case the problem now lies on the memory controller of the motherboard. Replace your board or let your system run in single channel mode.
Forum: Troubleshooting Dead Machines Oct 5th, 2007
Replies: 18
Views: 2,030
Posted By fren
Re: Pc doesnt start up

Maybe your motherboard does not support dual channel with two identical ram sticks which have more than 1.8 ram voltage. So it beeps when the two dimm slots are filled with sticks with unsupported...
Forum: IT Professionals' Lounge Oct 3rd, 2007
Replies: 2
Views: 1,766
Posted By fren
Re: how to place update files in AVG

Open AVG program.

Go to the Control Center.

Double Click on the Update Manager or select it then click the Properties button.

Untick the option "Do not ask for the update source", click Apply...
Forum: Windows NT / 2000 / XP / 2003 Oct 3rd, 2007
Replies: 2
Views: 381
Posted By fren
Re: Many many problems with windows

you will have to reinstall them again (antivirus, firewall, etc..). With regard to windows update, try to update again from the microsoft site. Problem persists, do a clean xp install.
Forum: Windows NT / 2000 / XP / 2003 Oct 3rd, 2007
Replies: 9
Views: 4,873
Posted By fren
Re: Windows XP Pro Install keeps rebooting

I think you will need to set your bios in default values then reboot. Set your settings again that you have before (if any). Next put your winxp cd then key the Ctrl-Alt-Del to restart your computer....
Forum: Troubleshooting Dead Machines Oct 2nd, 2007
Replies: 2
Views: 809
Posted By fren
Re: Bypassing old HD's password

How to take ownership of a folder. Try this one:

http://support.microsoft.com/default.aspx?scid=kb;en-us;308421&Product=winxp
Forum: Troubleshooting Dead Machines Oct 2nd, 2007
Replies: 1
Views: 487
Posted By fren
Re: Computer won't start until turning off/turning on PSU

Maybe your 20 pin power connector on the motherboard or from the power supply is loose or not properly connected to each other. Try to push all the wires towards to the motherboard socket.

If it...
Forum: Troubleshooting Dead Machines Oct 1st, 2007
Replies: 6
Views: 627
Posted By fren
Re: Motherboard problems...I think

It might be your power supply. A burnt power supply may also damage your motherboard. I hope not..
Forum: Storage Oct 1st, 2007
Replies: 4
Views: 1,112
Posted By fren
Re: Need help installing SATA card

Does your computer detect the card own bios? The card bios will post or appear on the screen upon starting. You will need a floppy disk drive to install a card driver.
Forum: Troubleshooting Dead Machines Sep 28th, 2007
Replies: 3
Views: 411
Posted By fren
Re: restarting prob :S

Before anything else, try to repair your operating system. Remember, back up all your files. Sometimes it might be a software problem. Be ready to have some program cds that needs to be reinstalled...
Forum: Storage Sep 28th, 2007
Replies: 10
Views: 798
Posted By fren
Re: IDE and SATA, need help =[

Try connecting it first in your computer. Set your new ide hdd as master in the primary controller and temporarily remove your sata drive then boot your system just to see if the bios detect your ide...
Forum: Troubleshooting Dead Machines Sep 28th, 2007
Replies: 4
Views: 592
Posted By fren
Re: HDD problems

Since your computer kept restarting, sometimes it was a software problem. Why don't you try to start from scratch again. Do a clean install. If you are still unable to do a clean install on the hard...
Forum: Storage Sep 27th, 2007
Replies: 10
Views: 798
Posted By fren
Re: IDE and SATA, need help =[

Be sure the ide hard disk drive is spinning. If not, try powering it up with different power connectors.

Check the ide hdd into another computer.
Forum: Troubleshooting Dead Machines Sep 27th, 2007
Replies: 4
Views: 592
Posted By fren
Re: HDD problems

I am not 100% sure if you can retrieve your files in your hard disk by connecting it as slave to another computer. Try it.
Forum: Troubleshooting Dead Machines Sep 27th, 2007
Replies: 2
Views: 564
Posted By fren
Re: Boot Problems

Clear the cmos through the pin jumpers or battery. Boot your system.
Showing results 1 to 40 of 402
Page 1 of 11 1 2 > Last »

 
Forums | Blogs | Tutorials | Code Snippets | Whitepapers | RSS Feeds | Advertising
All times are GMT -4. The time now is 2:41 am.
Newsletter Archive - Sitemap - Privacy Statement - Acceptable Use Policy - Contact Us
Forum system based on vBulletin Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.
©2003 - 2008 DaniWeb® LLC