 |  |  |  |  |  |  |  |
PC Freezes at POST No keyboard Input
 |
Ok, A buddy of mine recently asked me o fix his pc that some idiot custom built for him. I have worked on hundreds of computers starting when I was only 9 years old. Never found a computer that I couldn't fix. I have my A+, MCP and I'm also a college student for network administration.
The way the computer was running I deemed it a hardware issue and told him that he would need to replace his motherboard to fix the problem. It seemed that the processer wasn't pulling information from the ram the right way seeing as fedora core 6 was running INCREDIBLY slow with many errors.
He told me to dissasemble the PC and save whatever hardware was good. While I was dissaembling it I noticed that the douche bag who built the computer didn't set the processor in the socket all the way and there were some pins that were not in. So i reset the processor in the socket and figured that was the problem. While I was disssembling the computer I had taken the CMOS battery out. I put eveyrthing back in including the Battery and when I started the coputer it got an error that said syste, date not set or bad checksum. Plus the computer is not taking any input from the ps/2 keyboard, although the lights on the keyboard to light up when the computer starts. I cleared the CMOS by moving the jumper on the motherboard to position 1-2 and then put it back to position 2-3. Now whenever I start the computer it freezes at the post for a few minutes then goes to a message that says "default BIOS setting used" or something to that effect. I cann't use f1 to enter the BIOS or anything.
Any ideas?
the pc specs are as follows:
p4 2.6ghz with HT
2 GB DDR 2700.
250GB HDD.
DVD Burner.
The board was a pull from a HP PC and it has Intel Chipset.
The way the computer was running I deemed it a hardware issue and told him that he would need to replace his motherboard to fix the problem. It seemed that the processer wasn't pulling information from the ram the right way seeing as fedora core 6 was running INCREDIBLY slow with many errors.
He told me to dissasemble the PC and save whatever hardware was good. While I was dissaembling it I noticed that the douche bag who built the computer didn't set the processor in the socket all the way and there were some pins that were not in. So i reset the processor in the socket and figured that was the problem. While I was disssembling the computer I had taken the CMOS battery out. I put eveyrthing back in including the Battery and when I started the coputer it got an error that said syste, date not set or bad checksum. Plus the computer is not taking any input from the ps/2 keyboard, although the lights on the keyboard to light up when the computer starts. I cleared the CMOS by moving the jumper on the motherboard to position 1-2 and then put it back to position 2-3. Now whenever I start the computer it freezes at the post for a few minutes then goes to a message that says "default BIOS setting used" or something to that effect. I cann't use f1 to enter the BIOS or anything.
Any ideas?
the pc specs are as follows:
p4 2.6ghz with HT
2 GB DDR 2700.
250GB HDD.
DVD Burner.
The board was a pull from a HP PC and it has Intel Chipset.
•
•
Join Date: Mar 2007
Posts: 55
Reputation: 
Solved Threads: 2
Junior Poster in Training
If checksum fails, the BIOS reverts to using its built-in default settings.
A system crash or electrical spike can corrupt the BIOS file. Is the MB seated correctly?
Also, you might want to check your MB battery.
You may find that the BIOS chip may need to be reflashed, reprogrammed, or replaced. Which is bad news!!!
Time for a new MB
A system crash or electrical spike can corrupt the BIOS file. Is the MB seated correctly?
Also, you might want to check your MB battery.
You may find that the BIOS chip may need to be reflashed, reprogrammed, or replaced. Which is bad news!!!
Time for a new MB Last edited by darren2005; Nov 18th, 2008 at 12:34 pm.
•
•
Join Date: Aug 2007
Posts: 89
Reputation:
Solved Threads: 5
Junior Poster in Training
hello
Is the key board you are using USB? if it is you might need to change to PS/2 that is assuming that the BIOS system is too old. but all the same try using a PS/2 keyboard and see what happens. then if it works you can access the BIOS and make any changes you deem necessary.
Is the key board you are using USB? if it is you might need to change to PS/2 that is assuming that the BIOS system is too old. but all the same try using a PS/2 keyboard and see what happens. then if it works you can access the BIOS and make any changes you deem necessary.
three things in life must not be lost.
Faith:
Hope &
Love. But if the first 2 should be lost then please don't lose LOVE.
Faith:
Hope &
Love. But if the first 2 should be lost then please don't lose LOVE.
No I listed up above the type of keyboard it is. It is a ps2 keyboard and I have tried a few different ones to make sure my keyboard wasn't faulty. When the computer turns on the lights on the keyboard do light up so there is power getting to it... but the computer just doesnt want to take input from it. The Mobo is seated correctly and and the battery is new. I reset the CMOS and I guess the only thign I have left to do is to flash the bios. Does anyone have ny idea on how to do this. I have flashed the Bios on systems before but they were complete systems by dell and hp and I was able to get the proper flash off the website. All i know is that the motherboard is a pull from a HP PC and it has an Intel chipset.
•
•
Join Date: Mar 2007
Posts: 55
Reputation:
Solved Threads: 2
Junior Poster in Training
•
•
•
•
Originally Posted by firekid1239 
No I listed up above the type of keyboard it is. It is a ps2 keyboard and I have tried a few different ones to make sure my keyboard wasn't faulty. When the computer turns on the lights on the keyboard do light up so there is power getting to it... but the computer just doesnt want to take input from it. The Mobo is seated correctly and and the battery is new. I reset the CMOS and I guess the only thign I have left to do is to flash the bios. Does anyone have ny idea on how to do this. I have flashed the Bios on systems before but they were complete systems by dell and hp and I was able to get the proper flash off the website. All i know is that the motherboard is a pull from a HP PC and it has an Intel chipset.
This would be a good site for you to refer to http://www.wimsbios.com/faq.jsp
Well I need to figure out what type of BIOS my board has. All I know is that it was a pull from a HP system because during the POST is the " HP Invent" screen... the BIOS chip itself is not removable and it attached to the board and there is a sticker on it that "Stingray". Would it have anything to do with the Chipset? It has an Intel chipset thats all I know. I really have no problem flashing the BIOS, because either way the board is going in the trash. If I can't find a BIOS flash: Trash. If I mess up the BIOS flash: Trash.
A freind of mine who has a degree in Computer Programming as Well as Network Administration told me one other thing I could try was to push the power button and hold it in to turn the computer off 3 times. He said most modern BIOS's will recognize that it is not booting. On the 4th time he told me to hold in the Ctrl+End keys and I would hear a series of beeps and the CMOS would completely clear itself. He told me I couldn't have anything plugged in other than the keyoboard. Well I tried it and it didn't work for me.
Any other sugegstions would be nice. After all that why I'm here.
-Josh
A freind of mine who has a degree in Computer Programming as Well as Network Administration told me one other thing I could try was to push the power button and hold it in to turn the computer off 3 times. He said most modern BIOS's will recognize that it is not booting. On the 4th time he told me to hold in the Ctrl+End keys and I would hear a series of beeps and the CMOS would completely clear itself. He told me I couldn't have anything plugged in other than the keyoboard. Well I tried it and it didn't work for me.
Any other sugegstions would be nice. After all that why I'm here.
-Josh
•
•
•
•
Originally Posted by darren2005
The precise details for recovering from a corrupted BIOS varies for the different BIOS distributions, but typically involve recovering a working version of BIOS code from a floppy disk/CD when corrupt.
This would be a good site for you to refer to http://www.wimsbios.com/faq.jsp
Oh btw, thanks Darren2005, that site was pretty helpful. It didn't really give me a whole lot of options for my situation, but I did learn quite a bit about BIOS in general, things that I didn't know.
•
•
Join Date: Mar 2007
Posts: 55
Reputation:
Solved Threads: 2
Junior Poster in Training
•
•
•
•
Originally Posted by firekid1239
Well I need to figure out what type of BIOS my board has. All I know is that it was a pull from a HP system because during the POST is the " HP Invent" screen... the BIOS chip itself is not removable and it attached to the board and there is a sticker on it that "Stingray". Would it have anything to do with the Chipset? It has an Intel chipset thats all I know. I really have no problem flashing the BIOS, because either way the board is going in the trash. If I can't find a BIOS flash: Trash. If I mess up the BIOS flash: Trash.
A freind of mine who has a degree in Computer Programming as Well as Network Administration told me one other thing I could try was to push the power button and hold it in to turn the computer off 3 times. He said most modern BIOS's will recognize that it is not booting. On the 4th time he told me to hold in the Ctrl+End keys and I would hear a series of beeps and the CMOS would completely clear itself. He told me I couldn't have anything plugged in other than the keyoboard. Well I tried it and it didn't work for me.
Any other sugegstions would be nice. After all that why I'm here.
-Josh
You really need to find out what MB you have in order to go forward with this.
There is a "Stingray" MB with the model PTS73 (see http://support.packardbell.com/uk/it...ppn=PC14104001)
•
•
•
•
Originally Posted by darren2005
Thought that site would be useful to you!
You really need to find out what MB you have in order to go forward with this.
There is a "Stingray" MB with the model PTS73 (see http://support.packardbell.com/uk/it...ppn=PC14104001)
Hmmm... I know my board is a HP pull because of the "HP Invent" POST screen, but it's not that packard bell, I don't have pci express. Although the board is new enough that it has serial ATA. All I know it that is has an intel chipset, and there is a sticker on the bios chip (which I'm pretty sure is the BIOS chip) (it right in between the battery and the jumper to reset the CMOS) that says stingray.
What would be the easiest way to figure out what kind of board I have? There were tools on that site that darren2005 posted, but they require the OS to be running...
My buddy Mark gave me a wonderful little disc called Hiren's Boot CD which has hundreds of little tools on it including analyzers which should tell me what hardware I'm using in great detail... I just gotta figure out how to get the pc to boot from the CD drive...
*siiiigh*... **** my life...
•
•
Join Date: Mar 2007
Posts: 55
Reputation:
Solved Threads: 2
Junior Poster in Training
•
•
•
•
Originally Posted by firekid1239
Hmmm... I know my board is a HP pull because of the "HP Invent" POST screen, but it's not that packard bell, I don't have pci express. Although the board is new enough that it has serial ATA. All I know it that is has an intel chipset, and there is a sticker on the bios chip (which I'm pretty sure is the BIOS chip) (it right in between the battery and the jumper to reset the CMOS) that says stingray.
What would be the easiest way to figure out what kind of board I have? There were tools on that site that darren2005 posted, but they require the OS to be running...
My buddy Mark gave me a wonderful little disc called Hiren's Boot CD which has hundreds of little tools on it including analyzers which should tell me what hardware I'm using in great detail... I just gotta figure out how to get the pc to boot from the CD drive...
*siiiigh*... **** my life...
You might also find the BIOS version when the system first starts-up (above or below a logo - if applicable).
To be honest, you might end up trashing this MB!
Last edited by darren2005; Nov 20th, 2008 at 5:42 pm.
|
Other Threads in the Troubleshooting Dead Machines Forum
- Previous Thread: BIOS Rom Checksum Error
- Next Thread: My computer freezes on start up
| Thread Tools | Search this Thread |
You need to join our community in order to build your list of favorite forums. You can visit the forum index for a listing of all forums.
Latest Troubleshooting Dead Machines Posts
- Today's Posts
- Unanswered Threads
Related Forum Features
6 appliances beep bioslosingharddrived bioslosingsettings black bsod citrix cmosbattery compaq cpu dead delldimension4500 disk failure giving harddrive laptop linux mac mobo neverbuyinspiron1525 nodisplay nopower operatingsystemnotfound osnotfound pc power ram redhat screen supply ubuntu virtualbox virtualization virtualmachines vmware xen
