XFX mobo -> cd drive connectivity problem
 

i have a xfx-nf24-alh that can see the cd drives connected to it but can't boot from any of them.......it can't see the floppy drive at all (which only bothers me slightly

i know it's probably a hardware problem, but just in case it's a bios setting i haven't noticed or figured out i thought i'd check first before i take a hammer to it

Re: XFX mobo -> cd drive connectivity problem
 

Hi spookfish, and welcome.

I wasn't able to find a manual available for download for that motherboard, so I can't give you specific instructions, but as it is an nForce2 mobo the procedure should be rather starightforward.

Somewhere in your BIOS Setup menus, probably in the 'Advanced' section, you will find entries for:
1st boot device
2nd boot device
3rd boot device.....

and so on. Change the entry for '1st boot device' to CD-ROM, ensure that 2nd boot device is set to your system drive, and that there are no entries duplicated. Save and exit from BIOS setup, and watch for a message indicating "To boot from CD-ROM please press any key"

The message will only display for a few seconds, and if you don't press a key, it will bypass the CD drive and look for another device to boot from. (You may already have it set this way, and simply be missing the message when it displays ;))

Re: XFX mobo -> cd drive connectivity problem
 

i've had it set like that most of the attempts and it's come with no option to boot from the cd drives (unless it was going too fast for me to see) it checks both cd drives for a bootable cd and fails each time, even tho i know the cd in the drive can be booted from

i've even installed 98 onto the hard disk with this computer, switched the drive back to that mobo and 98 can't find any cd drive either

does it sounds plausable to have a hardware fault on an ide line/connection that can see a disk but can't communicate with it?

Re: XFX mobo -> cd drive connectivity problem
 

Set 1st boot device to CD-ROM
Set all other boot devices to 'none' or 'disabled'.

That'll get it working. The message is generally a small line of text at bottom of screen.

Re: XFX mobo -> cd drive connectivity problem
 

still no joy, i even tried switching a cd drive to the same ide line as the hard disk, it would seem this motherboard just isn't happy with optical drives

Re: XFX mobo -> cd drive connectivity problem
 

Have another look around in BIOS and see if you can find settings for 'IDE PIO' mode. Make sure they are set to 'Auto'.

Re: XFX mobo -> cd drive connectivity problem
 

yup, i did some hunting and found those very settings, got the floppy to work too, so now i've got a computer with a very buggy installation of xp that doesn't want to re-install :( but i'll get that sorted myself...eventually

thanks for all the advice tho

Re: XFX mobo -> cd drive connectivity problem
 

Do a format/fresh install.

The link in my sig will lead to a couple of articles about doing the job, and you should ideally remove the existing partition(s) and create a new one in its place. that'll give you the cleanest installation of Windows you can get ;)

Reinstalling over the top of a buggy installation is NEVER a good idea!

Re: XFX mobo -> cd drive connectivity problem
 

i think there's something still no 100% about the cd drive settings in the bios, i have a few xp boot cd's and they look unscratched but xp still doesn't install, it keeps coming back with read errors, files not matching the disk image or something, the drive is next to new, and the cd has only been out of it's packet one other time, so i'm guessing it's getting confused somewhere down the line

Re: XFX mobo -> cd drive connectivity problem
 

Oh, i'm sorry - the earlier advice I gave should have been to ensure that both 'IDE PIO' and 'IDE DMA' options are set to 'Auto'. If you have both of those in BIOS setup, see if that makes any difference.

Other than that, double check that the identification jumpers on your drives are set to 'Master' and 'Slave' accordingly, that 'Master' drives are connected to the end connector of the data cable and that 'Slave' drives are connected to the middle connector.

"Cable select' settings might sound all dinky and cute, but they introduce more chances of error, IMO.