Forum: Networking Hardware Configuration Jul 26th, 2005 |
| Replies: 20 Views: 15,582 Reset your router, there should be a reset button on device. It will bring back to router default configuration. Look at their website, it's normally, 192.168.x.1. After reset then connect one of... |
Forum: Networking Hardware Configuration Jul 24th, 2005 |
| Replies: 20 Views: 15,582 Let's go back to router. If you intend to use this router with its DCHP Server off, then it would act as a Hub/switch. Can you turn off also the WAN off? If you do then it's consider as a... |
Forum: Networking Hardware Configuration Jul 22nd, 2005 |
| Replies: 20 Views: 15,582 Cool, it's now look much better :-)
IF all PCs are Win98 then PC2 needs to have sygate (Last time when I used was 4 years ago).
IF PC2 with Win2k then would probably work (I don't have Win2k,... |
Forum: Networking Hardware Configuration Jul 21st, 2005 |
| Replies: 20 Views: 15,582 I tried to imagine what you want to do but I could not fully understand.
Try this configuration:
Building1:
DLS-Line <---> DSL_Modem<--->Wireless_Router<--PC1-Wired and PC2-Wired
PC1 and... |
Forum: Networking Hardware Configuration Jul 20th, 2005 |
| Replies: 20 Views: 15,582 Why do you have to have two routers (1 Wireless and 1 wired routers)?
Anyway, try this:
Phoneline/Cable<-->DLS/Cable-modem <--- Wireless router~~~>WirelessPC
Continue:
... |
Forum: Networking Hardware Configuration Jul 20th, 2005 |
| Replies: 1 Views: 1,558 (Internet)~~~ Phone-Line<--->DSL-Modem<---->Router/Wireless---->Wired/Network-PC1
PC2 Wireless connect wirelessly to Wireless/DSL-router
No Problem
Remember to remove firewall in XPSP2 and... |
Forum: Networking Hardware Configuration Jul 20th, 2005 |
| Replies: 7 Views: 4,496 If it's in the laptop, you probably check whether the antenna are well plugged in to miniPCI card. Also, Do not have Microwave or Cordless phone 2.4GHz on. If you laptop has also bluetooth then turn... |
Forum: Networking Hardware Configuration Jul 13th, 2005 |
| Replies: 14 Views: 10,326 Thanks! w1r3sp33d, that was good and very nice of you. |
Forum: Networking Hardware Configuration Jul 12th, 2005 |
| Replies: 14 Views: 10,326 Please see the show run - Thnks. Timolthy
PC
||
Catalyst 2950 Port/12 <----- Hub ------> Cisco Router... |
Forum: Networking Hardware Configuration Jul 12th, 2005 |
| Replies: 14 Views: 10,326 Trinity was so good !
Please shred the light further:
"Well, put you ip helper-address command on the interface that receives the broadcasts, then in global config mode enter the command: ip... |
Forum: Networking Hardware Configuration Jul 11th, 2005 |
| Replies: 14 Views: 10,326 Hi w1r3sp33d,
It was a while that I was no able to resume.
I did setup as you suggested. the VLANs can communicate between Vlans; however, they can not get IP address from the DHCP server. Only... |
Forum: Networking Hardware Configuration May 25th, 2005 |
| Replies: 14 Views: 10,326 Thank you for the Post. I just checked ebay, yea, 2620 is about less than $200 used. I am looking for router with two 100MB ports - are there exist? or would be way more expensive?
Other note: ... |
Forum: Networking Hardware Configuration May 23rd, 2005 |
| Replies: 14 Views: 10,326 THANK you very much for your generous and kindness Help. I will try it tonite. I should by 1721 instead of 1720 :(. I will look at Ebay to see any good deal on 1721.
Timolthy |
Forum: Networking Hardware Configuration May 23rd, 2005 |
| Replies: 14 Views: 10,326 Hey,
I have 2912 catalyst with simple setting total 3 vlan (192.168.1.x, 2.x, and 3.x) - the default ip is 192.168.1.10.
port 1,2,3,4 Vlan 1,
Port 5,6,7,8- Vlan 2
port 9,10,11,12 - vlan3
... |