| | |
Vista BlueScreen
![]() |
•
•
Join Date: Dec 2007
Posts: 38
Reputation:
Solved Threads: 0
I am getting the BlueScreen at some times while I'm on the computer. The error message is as follows:
"A problem has been detected and Windows has been shut down to prevent damage to your computer.
A wait operation, attach process, or yield was attempted from a DPC routine.
If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again follow these steps:
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask you hardware or software manufacturer for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical information:
*** STOP: 0x000000B8 (0x89A21170, 0x847559D8, 0x89A0E000, 0x00000000)
Collecting data for crash dump...
Initializing disk for crash dump...
Beginning dump of physical memory.
Dumping physical memory to disk: 100
Physical memory dump complete.
Contact your system admin or technical support group for further assistance."
Now this is a brand new computer of only 3 weeks. I don't have any newly installed hardware on my computer either. This has been happening for a couple days now and I want to get it solved. Anybody know how to solve this?
"A problem has been detected and Windows has been shut down to prevent damage to your computer.
A wait operation, attach process, or yield was attempted from a DPC routine.
If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again follow these steps:
Check to make sure any new hardware or software is properly installed. If this is a new installation, ask you hardware or software manufacturer for any Windows updates you might need.
If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use Safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.
Technical information:
*** STOP: 0x000000B8 (0x89A21170, 0x847559D8, 0x89A0E000, 0x00000000)
Collecting data for crash dump...
Initializing disk for crash dump...
Beginning dump of physical memory.
Dumping physical memory to disk: 100
Physical memory dump complete.
Contact your system admin or technical support group for further assistance."
Now this is a brand new computer of only 3 weeks. I don't have any newly installed hardware on my computer either. This has been happening for a couple days now and I want to get it solved. Anybody know how to solve this?
•
•
Join Date: Sep 2007
Posts: 19
Reputation:
Solved Threads: 0
Join the club! 
Does it work if you boot into safe mode?

Does it work if you boot into safe mode?
www.ihatevista.co.uk - What do you think of Vista?
Well from the source which i use it gives me this:
"These are generally hardware issues (which often means driver issues). The articles given below are provided more as examples of the types of situations that trigger this error, rather than concrete solutions. As a rule, be sure you have the latest Service Pack edition of your Windows operating system and are using the best device drivers and software versions. After that, do normal hardware troubleshooting for the device implicated."
have you installed any new hardware recently into your computer, such as graphics cards, hard-drives, USB devices etc. ?
If so check that you have the latest drivers for all the hardware you have. I don't know the process through Vista, but it may be similar to XP, where you go into Control Panel and look for System and then inside system there should be a tab called Hardware, then click onto Device Manager. This is the XP route to find what is needed to be found, in Vista it may be slightly different. Once you have found Device Manager double click onto each of the devices, and click onto the "Driver" tab, then click onto the "Update Driver" button. It will then tell you if you have the most up to date driver for that piece of Hardware.
I hope that helps!
"These are generally hardware issues (which often means driver issues). The articles given below are provided more as examples of the types of situations that trigger this error, rather than concrete solutions. As a rule, be sure you have the latest Service Pack edition of your Windows operating system and are using the best device drivers and software versions. After that, do normal hardware troubleshooting for the device implicated."
have you installed any new hardware recently into your computer, such as graphics cards, hard-drives, USB devices etc. ?
If so check that you have the latest drivers for all the hardware you have. I don't know the process through Vista, but it may be similar to XP, where you go into Control Panel and look for System and then inside system there should be a tab called Hardware, then click onto Device Manager. This is the XP route to find what is needed to be found, in Vista it may be slightly different. Once you have found Device Manager double click onto each of the devices, and click onto the "Driver" tab, then click onto the "Update Driver" button. It will then tell you if you have the most up to date driver for that piece of Hardware.
I hope that helps!
The Great Lord, Serunson.
Epic Hedgehog power all the way!
Quote from scru :: "If you were a file I'd hit delete."
Epic Hedgehog power all the way!
Quote from scru :: "If you were a file I'd hit delete."
Do you have the printer connected through a USB cable or through a wireless router (if you have a wireless network)?
Does the BSOD always appear when you have the printer plugged in? If yes then try the computer without the printer plugged in and see if it still BSOD's then the problem may be with the drivers to the printer. To try and avert the problem uninstall the drivers for the printer, reboot the computer and reinstall them.
Otherwise this could be due to a virus/spyware attack. What Anti-Virus/Anti-Spyware do you run?
Does the BSOD always appear when you have the printer plugged in? If yes then try the computer without the printer plugged in and see if it still BSOD's then the problem may be with the drivers to the printer. To try and avert the problem uninstall the drivers for the printer, reboot the computer and reinstall them.
Otherwise this could be due to a virus/spyware attack. What Anti-Virus/Anti-Spyware do you run?
The Great Lord, Serunson.
Epic Hedgehog power all the way!
Quote from scru :: "If you were a file I'd hit delete."
Epic Hedgehog power all the way!
Quote from scru :: "If you were a file I'd hit delete."
![]() |
Similar Threads
- Vista - restart problem (Windows Vista and Windows 7)
Other Threads in the Windows Vista and Windows 7 Forum
- Previous Thread: Windows Media Player 11 in Vista.
- Next Thread: Vista Wireless problems
| Thread Tools | Search this Thread |
.net 3.5 7 activation advertising aero android apple appstore azure ballmer battery beta betatesting billgates blackberry blog bsod classpnp.sys cloudcomputing code commandprompt computer desktop development downloads drm earnings economy error fiji folderstructures folderview france freeze gartner google hp http://www.expertcore.org/ internetexplorer iphone licensing linux mac mal merger microsoft midori mobile mojave monopolies mp3 netbook news open operating operatingsystem operatingsystems opinion os osx parliament patch patents pc petabyte product redhat research russia schools screen security seinfeld server software sp1 sp3 steveballmer streamingmedia survey system techcrunch touchscreen touchwall ubuntu upgrade virtual virtualization vista voip win7 windows windows7 windowsmobile windowsvista windowsxp wpf xp yahoo






