Floppy drive won't work, won't read disks :(

•

What is DaniWeb IT Discussion Community?

You're currently browsing the Windows 9x / Me section within the Tech Talk category of DaniWeb, a massive community of 456,534 software developers, web developers, Internet marketers, and tech gurus who are all enthusiastic about making contacts, networking, and learning from each other. In fact, there are 2,968 IT professionals currently interacting right now! Registration is free, only takes a minute and lets you enjoy all of the interactive features of the site.

Join our community!

Please support our Windows 9x / Me advertiser: 64-bit Windows Community

Thread Tools Display Modes

Views: 11495 | Replies: 2

•

Join Date: Aug 2004

Posts: 2

Reputation: lostouten is an unknown quantity at this point

Rep Power: 0

Solved Threads: 0

lostouten

Offline

Newbie Poster

Floppy drive won't work, won't read disks :(

Aug 10th, 2004

My floppy drive a:\ will no longer work. As far as I know, I didn't do anything that should have caused it to quit (like installing new software or hardware). It just didn't work one day. I have tried removing the driver, removing the device, and opening the case to make sure everything is still connected to the drive. After all that, I figured the drive was bad, and bought a new one. Guess what - it won't work either! I still get an error message reading: "a:\ is not accessible. the device is not ready." I can hear noises coming from the drive, so I know it has power. Oh, and I also tried reformating one of the disks - won't work. Somehow, it doesn't seem to be detecting there is a disk in the drive (I can shut down the computer without getting the warning from virus software about a disk in the A: drive). I run Windows98SE on an HP Pavilion 9680c.

Thanks,
Linda

•

Join Date: Jul 2004

Location: North East Indiana

Posts: 491

Reputation: Puckdropper is an unknown quantity at this point

Rep Power: 5

Solved Threads: 20

Puckdropper Puckdropper is offline

Offline

Posting Pro in Training

Re: Floppy drive won't work, won't read disks :(

Aug 11th, 2004

From the boot-up menu (press F8 when Windows begins to load...Same way to get in to safe mode.) select "Command Prompt Only" probably option 6.

From there:
--Put a disk in the drive
--type "A:" (no quotes)
--if you see "A:\>" for a prompt then type "dir" (without quotes).
--Observe the results. If there's directory listing, then your drive works properly. If not, then obviously the drive doesn't work right.

If your drive works properly
--------------------------
1) Boot into Windows.
2) From the device manager (System icon in Control Panel) remove the "Standard Floppy Disk Controller" under "Floppy Disk controllers" and reboot. You may want to power off before rebooting. (It sometimes works better that way.)

If your drive does not work properly
----------------------------------
1) Enter BIOS setup, (look for a prompt that says "Press key for setup")
2) depending on the system, under "standard bios setup" or something like that (it really differs) look for something referencing the floppy drive type.
3) If it's there, make sure it's settings are correct.
4) Exit the BIOS setup, saving changes if you intended to make changes. (If the settings were correct, do not save changes. It's possible to screw something up accidentally. Trust me ;-))

Oh yeah, did you put the cable back on exactly the same way? The red stripe should go to pin 1 on both the floppy and motherboard. If you need more help, just ask.

www.uncreativelabs.net

Old computers are getting to be a lost art. Here at Uncreative Labs, we still enjoy using the old computers. Sometimes we want to see how far a particular system can go, other times we use a stock system to remind ourselves of what we once had.