Floppy drive won't work, won't read disks :(

Expand Post »

My floppy drive a:\ will no longer work. As far as I know, I didn't do anything that should have caused it to quit (like installing new software or hardware). It just didn't work one day. I have tried removing the driver, removing the device, and opening the case to make sure everything is still connected to the drive. After all that, I figured the drive was bad, and bought a new one. Guess what - it won't work either! I still get an error message reading: "a:\ is not accessible. the device is not ready." I can hear noises coming from the drive, so I know it has power. Oh, and I also tried reformating one of the disks - won't work. Somehow, it doesn't seem to be detecting there is a disk in the drive (I can shut down the computer without getting the warning from virus software about a disk in the A: drive). I run Windows98SE on an HP Pavilion 9680c.

Thanks,
Linda

Similar Threads

formatting problems in Windows NT / 2000 / XP
problem with floppy drive-doesn't read in Storage
Floppy drive not responding in Storage
floppy drive stopped reading disks on HP laptop in Windows NT / 2000 / XP
Floppy drive shows as B drive instead of A in Storage

lostouten

Reputation Points: 10

Solved Threads: 0

Newbie Poster

Offline

2 posts
since Aug 2004

Permalink

Aug 11th, 2004

Re: Floppy drive won't work, won't read disks :(

From the boot-up menu (press F8 when Windows begins to load...Same way to get in to safe mode.) select "Command Prompt Only" probably option 6.

From there:
--Put a disk in the drive
--type "A:" (no quotes)
--if you see "A:\>" for a prompt then type "dir" (without quotes).
--Observe the results. If there's directory listing, then your drive works properly. If not, then obviously the drive doesn't work right.

If your drive works properly
--------------------------
1) Boot into Windows.
2) From the device manager (System icon in Control Panel) remove the "Standard Floppy Disk Controller" under "Floppy Disk controllers" and reboot. You may want to power off before rebooting. (It sometimes works better that way.)

If your drive does not work properly
----------------------------------
1) Enter BIOS setup, (look for a prompt that says "Press key for setup")
2) depending on the system, under "standard bios setup" or something like that (it really differs) look for something referencing the floppy drive type.
3) If it's there, make sure it's settings are correct.
4) Exit the BIOS setup, saving changes if you intended to make changes. (If the settings were correct, do not save changes. It's possible to screw something up accidentally. Trust me ;-))

Oh yeah, did you put the cable back on exactly the same way? The red stripe should go to pin 1 on both the floppy and motherboard. If you need more help, just ask.

Puckdropper

Reputation Points: 23

Solved Threads: 23

Posting Pro in Training

Offline

494 posts
since Jul 2004

Permalink

Aug 11th, 2004

Re: Floppy drive won't work, won't read disks :(

Thanks for the advice! I'll give that a try when I get home this evening.

-Linda

lostouten

Reputation Points: 10

Solved Threads: 0

Newbie Poster

Offline

2 posts
since Aug 2004

This thread is more than three months old

No one has posted to this discussion for at least three months. Please let old threads die and do not reply to them unless you feel you have something new and valuable to contribute that absolutely must be added to make the discussion complete. Otherwise, please start a new thread in this forum instead.

Previous Thread in Windows 95 / 98 / Me Forum Timeline: Windows Interface has changed..a serious problem!

Next Thread in Windows 95 / 98 / Me Forum Timeline: hard drive

DaniWeb Message

Cancel Changes

User Name
Password