P4 CPU Temperature

[TheBeast32]

Hi, I just replaced my 2.4 Ghz Intel Celeron CPU with a P4 Prescott at 3.2 ghz like 2 hours ago. It idles at like 48 degrees Celsius. I played half-life 2 for a bit and it went up to like 60-62. I didn't put any thermal crap on it. I have a new fan that says it supports up to 3.6 Ghz. Is this normal for my CPU, or if not what should I do?

The fan is a Thermaltake TR-M12 for socket 478

[crunchie]

Your answer is in your question.
Put some thermal compound between the IHS and HSF before you turn your cpu into a paperweight :).

[TheBeast32]

There was some thermal compound on the fan; is that not enough?

[crunchie]

Well, you said you didn't put any on. If it's the old stuff that was already on there, then no, it's not enough.
Arctic Silver 5 or MX-2 are the best to use. MX-2 is non-conductive.

Prescott's are known to run hot anyway, so the more help they get, the better.
Pretty sure they are designed to run ok even in the mid 70C's, but I wouldn't recommend 24/7 at those temps.

[TheBeast32]

The thermal compound on my fan was new. I had just taken the fan out of the box. I think I'll get some. Would it survive until like next weekend?

[crunchie]

I have used toothpaste (don't laugh) and it worked really well for a week until I got some thermal compound.
Make sure the HSF is sitting flat on the IHS. Some new heat sinks are not flat from the factory either, so if you have some way of checking it, I would do that too.

[TheBeast32]

Thanks for your help. I'll be sure to get some thermal compound.

[crunchie]

No worries :)

[The New Normal]

EDIT: IN THE TIME IT TOOK TO WRITE THIS 5 POSTS APPEARED. YOU SEEM TO HAVE SOLVED IT ;)

Ah, yes the compound that comes with the fan would be enough if it's brand new. You still need to clean the CPU surface first. It generally takes a day or so to work at it's best, but 62 seems a bit hot even for strait away.

The general rule is not to go above 60; apparently the Prescotts throttle down at 65 by inserting a few idle clocks here and there, reducing performance.

I would re-seat the heatsink with some quality goop like arctic silver 5, making sure to clean off all the other stuff with iso-propyl alcohol wipes. But that's just me.

Since your temps are not disastrous, you could wait and see if a few heating/cooling cycles (using and turning off) cures the goop and reduces your temps to below 60 under load.

[jbennet]

Late P4s are just generally very hot

I got one of the last P4s , a Cedar MIll 661, 3.6ghz stock. Overclocked it to 3.9.

It used to do 50-60 idle, and 60-70 under load ar the stock speed with the stock cooler

The P4s max temp is 65-75 . After that you risk damage..

Thats why intel scrapped the whole P4 Netburst atrchitechture at a huge cost and went back to the slower, but more efficient P3/pentium M architecture as the basis for the Core CPUs. You cant just keep increasing clock speeds.

But you should definately put new thermal paste and heatsink on. And good stuff. When i did that i got it down to 45-55 idle, and 60-65 under load

[TheBeast32]

WOOT! I got a case fan and put new thermal compound on my CPU and it is a lot cooler! It went down by almost 15 degrees Celsius. I'll play a game and see how hot it gets.

[crunchie]

Cool, (pun intended :D)

[cbusen]

I had no idea they called this glorified vasoline thermal compound....hmmm, i wonder if it a C5 or C6, anyway..i thought here or in another post i picked up that the thermal compounds couold have serious differences, brand to brand, in their ablity to conduct heat. Are there any brands to avoid for sure, and any you're almost always safe with? other than artic fox? like the one i'm holding right now, about to put on my CPU...dynex? is it bad?

Hi, I just replaced my 2.4 Ghz Intel Celeron CPU with a P4 Prescott at 3.2 ghz like 2 hours ago. It idles at like 48 degrees Celsius. I played half-life 2 for a bit and it went up to like 60-62. I didn't put any thermal crap on it. I have a new fan that says it supports up to 3.6 Ghz. Is this normal for my CPU, or if not what should I do?

The fan is a Thermaltake TR-M12 for socket 478

[cbusen]

I will be keeping a steady eye on the temp but i won't get a temp gauge. I live in Arizona and its summer, sorry for stating the obvious and you HAVE to keep air moving around these babies or, under gaming and certain circumstances you will fry 'em. IF you overclocked it, which i won't do. BUT, i do belive that no overclocking it and letting it run hot, dooms you to an earlier replacement. I think if you work the hell out of em in a hot room, its performance goes down faster and it hits the curb sooner