Ad:

Storage Discussion Thread
Unsolved
Views: 14737

Mar 30th, 2004

Error message when reading floppy in windows xp pro and dos boot

Expand Post »

I get this error message when I try accessing my floppy drive from windows xp

"A:\is not accessible. The floppy disk controller reported an error that is not recognized by the floppy disk driver"

and when I try to boot from a floppy i get
"please insert system disk" or something like that

any ideas? I have changed the floppy drive about 3 times, I put 2 different cables in. It's driving me crazy I have to reload my computer and I need the floppy. is my disk controller shot ? i have an asus p2b-f mobo

Similar Threads

Error message when booting or installing XP in Windows NT / 2000 / XP

viperman224

Reputation Points: 29

Solved Threads: 1

Junior Poster

Offline

183 posts
since Dec 2003

Permalink

Mar 30th, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

Quote originally posted by viperman224 ...

I get this error message when I try accessing my floppy drive from windows xp

"A:\is not accessible. The floppy disk controller reported an error that is not recognized by the floppy disk driver"

and when I try to boot from a floppy i get
"please insert system disk" or something like that

any ideas? I have changed the floppy drive about 3 times, I put 2 different cables in. It's driving me crazy I have to reload my computer and I need the floppy. is my disk controller shot ? i have an asus p2b-f mobo

The floppy drive controller is integral to the motherboard. If it's a hardware problem, it's probably gonna be a replacement motherboard needed, unless you can find an ISA-slot floppy controller (FDC) used somewhere.

On the other hand, there is another possibility, and I have seen this--a corrupted CMOS. Check your settings for the floppy controller in your setup screen. If they appear OK, try a Reset to default. If that doesn't do the trick, remove the CMOS battery (disc-shaped, near the CPU) from its socket for about 12 hours. There is no CMOS-reset jumper on the board, so far as I can tell. If that fails to do the trick, you may have to go the FDC-card route. Good luck.

TallCool1

Team Colleague

Reputation Points: 149

Solved Threads: 45

Practically a Posting Shark

Offline

865 posts
since May 2003

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

Quote originally posted by viperman224 ...

I get this error message when I try accessing my floppy drive from windows xp

"A:\is not accessible. The floppy disk controller reported an error that is not recognized by the floppy disk driver"

and when I try to boot from a floppy i get
"please insert system disk" or something like that

any ideas? I have changed the floppy drive about 3 times, I put 2 different cables in. It's driving me crazy I have to reload my computer and I need the floppy. is my disk controller shot ? i have an asus p2b-f mobo

Some of the new floppy drives are pretty wacky, they have the pin orientation reversed.
If your floppy cable is not keyed and the floppy activity light is on constantly, try flipping the floppy cable over at the end closest to the drive.

Does your floppy cable have a twist in it? If not, the floppy drive could be B:\

chanto!

Reputation Points: 45

Solved Threads: 1

Light Poster

Offline

39 posts
since Mar 2004

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

Another couple of points as well:

If that floppy drive is an old, used one, then try a new floppy drive. Windows XP seems to be a bit 'tochy' with older floppy drives

The other thing is - why do you need it?

You can install Windows XP by booting from the CD!

Catweazle

Team Colleague

Reputation Points: 229

Solved Threads: 149

Grandad

Offline

3,826 posts
since Mar 2004

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

I need the floppy to run the Western Digital program to test the drive because scandisk found lots of bad sectors when I did my lat reload. This is why I am reloading it because the machine is very unstable. The drive is under warrenty untill september of this year so if there is a problem with it I would like to fix it

The floppy cable I am using now has the twist in it but had been working before. I had bought a colored cable to go with my see-through case and thats when I noticed the problem. The cable was key but my floppy drive just has the plug and no special keyed feature so you can plug the cable in any way. I flipped my cable around serveral times and much to my dismay it still didn't work. thanks for the ideas I'll try and let you guys know how I make out with it. thanks

viperman224

Reputation Points: 29

Solved Threads: 1

Junior Poster

Offline

183 posts
since Dec 2003

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

If you're getting lots of bad sectors, then the drive has problems and you should be getting it replaced under warranty, not attempting to 'fix' it.

Catweazle

Team Colleague

Reputation Points: 229

Solved Threads: 149

Grandad

Offline

3,826 posts
since Mar 2004

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

yes, but the thing with western digital is before you can send the drive back you need an error code from their program if you send it back without the error code they won't send you a new one. my dad told this to me I have no idea if you need the error code but I assume you do. thanks for your help

viperman224

Reputation Points: 29

Solved Threads: 1

Junior Poster

Offline

183 posts
since Dec 2003

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

Quote originally posted by viperman224 ...

yes, but the thing with western digital is before you can send the drive back you need an error code from their program if you send it back without the error code they won't send you a new one. my dad told this to me I have no idea if you need the error code but I assume you do. thanks for your help

But what error code could possibly be worse than a bad sector? you don't get error codes for bad sectors? maybe you should try getting it replaced anyway. If they won't replace it then the warranty's no use at all...

oalee

Team Colleague

Reputation Points: 72

Solved Threads: 14

cyberkill(ed)

Offline

506 posts
since Feb 2004

Permalink

Mar 31st, 2004

Re: Error message when reading floppy in windows xp pro and dos boot

eerrr.... uummmmm................

Tell them the "error code" is xxxxxxxxxxxx bad sectors! Do you have Consumer Rights legislation where you live?

Catweazle

Team Colleague

Reputation Points: 229

Solved Threads: 149

Grandad

Offline

3,826 posts
since Mar 2004

This thread is more than three months old

No one has posted to this discussion for at least three months. Please let old threads die and do not reply to them unless you feel you have something new and valuable to contribute that absolutely must be added to make the discussion complete. Otherwise, please start a new thread in this forum instead.

Previous Thread in Storage Forum Timeline: A:\ not working

Next Thread in Storage Forum Timeline: 40 gig western digital permanent format in NTFS?

DaniWeb Message

Cancel Changes

User Name
Password