943,614 Members | Top Members by Rank

Hardware and Software > PC Hardware > Troubleshooting Dead Machines > Computer won't start after power outage.
Ad:
Permalink
Jan 13th, 2007
0

Computer won't start after power outage.

Expand Post »
Another poster seems to have a similar problem below but I didn't want to hijack his thread so here goes.

The power to my subdivision cycled off and on rapidly about 15 times the other morning. Afterwards my computer (HP a530n) wouldn't start. it gives no lights on the front and you don't hear anything inside happening (no fans spin up) on the back of the Computer the PSU LED is flashing.

I went through the online troubleshooting guide from HP and got to the point where you disconnect the PSU from everything to give you a solid green (if PSU is good) and then plug in things until the LED flashes again showing the fault. Well the first thing I unplugged after removing from the PSU was the Motherboardand decided I would go ahead and check the PSU LED as I disconnected things. Sure enough the PSU LED went solid green. So I decided to check out the PSU just to be sure by swapping it out with another that I had nearby in another desktop (call it computer #2). The PSU from Computer 2 went into Computer 1 and I get the fans to spool up for about a second before it powers back down. So I took the PSU from Computer 1 and placed it in Computer 2 and it started right up with no problems whatsoever.

So here is my question:
To me it looks like I have a bad Motherboard. Do you agree?

Or could it be one of the cards attached to the motherboard that is bad and that I need to unplug the individual cards from the motherboard to check them?
Similar Threads
Reputation Points: 10
Solved Threads: 0
Newbie Poster
Nucleartiger is offline Offline
3 posts
since Dec 2006
Permalink
Jan 15th, 2007
0

Re: Computer won't start after power outage.

Well I went ahead and disconnected all cards except the video card and tried to start it up with both PSUs. As before the computer does not respond at all with the original PSu and only respond for a bout a half second with the PSU from my old computer.

One thing that I forgot to mention before was that the motherboard has a 4 pin power point and the old psu that I was using for testing does not have that connector. Everything that I have read says that AMDs don't require that 4pin power connected to startup just that it will be unstable.

So If someone would please help me out here that would be great.

What do you think the problem with my computer is?

a) the motherboard/cpu is bad

b) the psu is bad

I think it is option a but any thoughts or suggestions before I go out and order a new mobo would be greatly appreciated.
Reputation Points: 10
Solved Threads: 0
Newbie Poster
Nucleartiger is offline Offline
3 posts
since Dec 2006
Permalink
Jan 16th, 2007
0

Re: Computer won't start after power outage.

Pardon me if I snicker here, but what do you suppose they mean by being unstable. You will need a PSU with the P4 connector if the motherboard has that connector.
dcc
Reputation Points: 138
Solved Threads: 36
Posting Virtuoso
dcc is offline Offline
1,525 posts
since Mar 2005
Permalink
Jan 16th, 2007
0

Re: Computer won't start after power outage.

I was afraid of that. Although like I said above I have seen multiple things online from people saying that the AMDs WILL work without that 4 pin connector.

I am just trying to figure out what the problem is without having to go out and buy stuff that I don't need.

Any other helpful responses are appreciated.
Reputation Points: 10
Solved Threads: 0
Newbie Poster
Nucleartiger is offline Offline
3 posts
since Dec 2006
Permalink
Jan 16th, 2007
0

Re: Computer won't start after power outage.

There is an adaptor that will allow you to use the 20 pin connector type PSU. It still won't have the p4 connector which can be a problem with some motherboards. I built a new machine recently that had the 24 pin connector and the p4 connector and had been advised from the tech support that there may be an issue with the system fully powering up without the p4 connector.

What motherboard and CPU are you using?
dcc
Reputation Points: 138
Solved Threads: 36
Posting Virtuoso
dcc is offline Offline
1,525 posts
since Mar 2005
Permalink
Jan 25th, 2007
0

Re: Computer won't start after power outage.

Click to Expand / Collapse  Quote originally posted by Nucleartiger ...
Well I went ahead and disconnected all cards except the video card and tried to start it up with both PSUs. As before the computer does not respond at all with the original PSu and only respond for a bout a half second with the PSU from my old computer.

One thing that I forgot to mention before was that the motherboard has a 4 pin power point and the old psu that I was using for testing does not have that connector. Everything that I have read says that AMDs don't require that 4pin power connected to startup just that it will be unstable.

So If someone would please help me out here that would be great.

What do you think the problem with my computer is?

a) the motherboard/cpu is bad

b) the psu is bad

I think it is option a but any thoughts or suggestions before I go out and order a new mobo would be greatly appreciated.
I have a simular problem just about everytime the power goes out.
Try this. Remove the power cord from the computer. Open up the box and disconnect the power supply from the mother board. Wait till the light on the power supply stops flashing (total discharge), then plug the power cord back in - the light should stay green after a second or two. Once the light is green - plug the power supply back into the mother board. If you see a solid green light on the mother board, turn the machine on RIGHT NOW!!

It will run till you turn it off.

Yes, something in the mother board is dying, but if your machine still runs, MAKE A BACKUP!
Reputation Points: 10
Solved Threads: 0
Newbie Poster
KevinTaute is offline Offline
2 posts
since Jan 2007
Permalink
Jan 26th, 2007
0

Re: Computer won't start after power outage.

those on and off voltage cycles also meant POWER SURGES, bad news for any system board. a new or reprogrammed BIOS is fairly cheap. if that doesn't work then it's time to consider another board, seems to me you've tried everything else.
Reputation Points: 13
Solved Threads: 26
Posting Pro
mechbas is offline Offline
579 posts
since Jan 2007
Permalink
Jul 22nd, 2009
0

Re: Computer won't start after power outage.

Click to Expand / Collapse  Quote originally posted by KevinTaute ...
I have a simular problem just about everytime the power goes out.
Try this. Remove the power cord from the computer. Open up the box and disconnect the power supply from the mother board. Wait till the light on the power supply stops flashing (total discharge), then plug the power cord back in - the light should stay green after a second or two. Once the light is green - plug the power supply back into the mother board. If you see a solid green light on the mother board, turn the machine on RIGHT NOW!!

It will run till you turn it off.

Yes, something in the mother board is dying, but if your machine still runs, MAKE A BACKUP!
After about a year, the power supply died on this machine (HP a530n). Replacing the power supply resulted in the problem going away.
Reputation Points: 10
Solved Threads: 0
Newbie Poster
KevinTaute is offline Offline
2 posts
since Jan 2007
Permalink
Sep 24th, 2009
0

Re: Computer won't start after power outage.

I'm having a similar problem. I took apart my computer to clean some of the dust out (something I've done in the past). Once I put everything back together I wasn't able to get it to start.

The LED on the motherboard is lit, but when I press the power button nothing happens.

I tried the method mentioned above (unplugging the power, unplugging the power supply from the mobo, plugging the power back in and then plugging the motherboard back in). Using this method, as soon as I plug the motherboard in the fans spin for a second or two then stop. The power button still does nothing.

I've tried jump starting it, switching the reset and power buttons (ie using the reset button as the power button), and I've triple checked that everything is connected correctly. Anyone have any insights into whats wrong? I don't think the motherboard is bad, as I mentioned the LED lights up indicating the motherboard has power.
Reputation Points: 10
Solved Threads: 0
Newbie Poster
NullPointer is offline Offline
1 posts
since Sep 2009

This thread is more than three months old

No one has posted to this discussion for at least three months. Please let old threads die and do not reply to them unless you feel you have something new and valuable to contribute that absolutely must be added to make the discussion complete. Otherwise, please start a new thread in this forum instead.
Message:
Previous Thread in Troubleshooting Dead Machines Forum Timeline: No display when turning on PC
Next Thread in Troubleshooting Dead Machines Forum Timeline: Ok very odd system issue please help





About Us | Contact Us | Advertise | Acceptable Use Policy
Forum Index | Build Custom RSS Feed


Follow us on Twitter


© 2011 DaniWeb® LLC