I am having problem with my ports, yesterday I opened port 80 and setup local area connection propeties for ipv4 to use static ip, I used ipconifg in cmd to check it first. I am using WAMP server on my pc with windows 7 64-bit. It worked ok.

But today ports are closed, and I didn't changed anything from yesterday. I tried to opened additional ports besides 80 like 8081,443, 8080 in my router with local ip like same setings in my ipv4 propeties to see if give some result, I disabled router firewall, allowed ports to go trough windows firewall, and added all ports for tcp and udp to my norton internet security, I tried also disabling whole firewall but same result.

WAMP is running and listening on port 80, 8081, 8080, 443.

When I check which program is using port 80, it says Apache/2.4.9 <Win64> PHP/5.5.12

I noticed that all other ports except 80 and 443 are closed, but 80 and 443 are refusing connection if router firewall is off, and if its on they are closed also. And yesterday I had router firewall on, norton firewall on, and no rules for windows firewall, and it worked.

Thanks for your help in advance.

Recommended Answers


The best advice I can give is to go back to the basics.
- Run ipconfig again and make usre you still have the same IP.
- If you are on a router that is running DHCP and assigning addresses it may have given the address to something …

Jump to Post


If you use a static IP in the range that your router is using for DHCP then you can create conflicts if DHCP assigns that address. Normally DHCP is set up for 254 addresses ( - but some of the newer routers only assign 100. I suggest either …

Jump to Post


OK based on what you posted your DHCP server is only assigning addresses from - which still puts as an address it could give to a cell phone using WiFi or any other computer that connects. I suggest moving the system with the static address to …

Jump to Post

You should block your public IPs when posting (better safe than sorry).

With that, we are now certain it is not the router, network, or other host.

So now we concentrate on your web server. Like I said, there is something else listening on port 80.

This is a windows …

Jump to Post

Does [chrome] appear above or below the TCP 80 LISTENTING? In the output, the service appears after the listening port.

Jump to Post

All 41 Replies

How about you directly access the and but some IMCP's on the server for when the ports get closed so you can run a diagnostic.

What do you mean? When I test which program is using port 80, it says apache.

Sanity check.

From your Windows PC with the open ports, use the online tool http://canyouseeme.org This will give you your current public IP, plus it will allow you to test for open ports on that IP. Nifty tool to check for open ports.

I did used that already, and other tools to check, ports are closed always, except when I turn router firewall down, then port 80 and 443 are not closed but refusing connection, and all other ports remains closed.

Other items off top of my head.

  • check that the port forward is hitting the correct internal IP for this host.

  • Can the ports can be hit from inside the network from another PC? (eliminated router if no)

  • From the host in question, netstat -ab will display listening ports and the process that owns it. Make sure you don't have 2 processes fighting over same ports.

  • Load wireshark on the win host. As you try to access from the outside and get the apache response, does wireshark record packets to that host? If yes, then my guess about 2 competing processes looks pretty good.

I know for sure that internal ip is right, I even setup in local area connection static ip and connected ports to that ip, my server was able to be reached first day, and ports were open, next day ports were closed or refusing connection, depending on port and firewall statuts, but I changed nothing from last day,

I will try wireshark, at the moment I tested port 80 and it said its used by apache only

What I"m getting at is, either apache is running on that host (unbeknownst to you) and fighting for control over port 80 or internal networking is messed up and you are sending traffic to another host running 80.

LEt me know what you find.


The best advice I can give is to go back to the basics.
- Run ipconfig again and make usre you still have the same IP.
- If you are on a router that is running DHCP and assigning addresses it may have given the address to something else. If you are going to set a static IP then either set your DHCP service in the router to start at an address above the static ones you want to use (i.e. starting at instead of
- Check WAMP and make sure it has started since you last checked.
- Ping the IP from a command prompt (on the server and on a different system) and see if you get a response.
- Go to Control Panel, Programs and Features and click Turn WIndows Features on or off on the upper left. When the dialog box comes up (takes a while some times) scroll down and find Telnet Client and check it to install the client. Once it is installed you can go to a command prompt and attempt to telnet directly to the port and the apache server should respond:

telnet 80

Hope this help and Let us know how it goes.

I know that happygeek. It's because of freaking auto-correct.

with ipconfig ip is still, but I noticed in DHCP something, before I had two PC's connected to it, PC which uses Wireless and its on ip and my PC is not there anymore, maybe because I setup static ip in local area, not automaticly assigned.

DHCP have option Client IP Pool Starting Address and its set to


If you use a static IP in the range that your router is using for DHCP then you can create conflicts if DHCP assigns that address. Normally DHCP is set up for 254 addresses ( - but some of the newer routers only assign 100. I suggest either moving your PC to a much higher number instead of (like so there will be no issues. Either that or like I said before set the starting number for DHCP to a higher value.

One other question what do you have set for the netmask and gateway for the static IP address in properties under local area connection? It should be something like this:


Hope this helps

This is picture of local area Click Here

This is picture of DHCP in router options Click Here, Dejan-PC is another PC connected via wireless, my PC was there also before was setup to asign automaticly ip.

This is NAT port forwarding picture Click Here

I am wondering what is changed since everything worked fine, because router setings were same as they are now.


OK based on what you posted your DHCP server is only assigning addresses from - which still puts as an address it could give to a cell phone using WiFi or any other computer that connects. I suggest moving the system with the static address to something outside that range ( would be easy to remember and change). Then adjust your settings accordingly in the router. On the page listing port forwarding addresses you would need to change it to match and normally there are settings for http, ftp, etc that will auto configure the ports and protocols for you.

But before you start trying to connect externally you need to make sure that you can reach the web site locally (inside your own LAN or local area network). Try connecting to the web site from the PC at 1.3 and also make sure that you can ping the address from that system. If you can ping it ok try the telnet connection I suggested earlier and see if you get a web page back.

I changed ip to and added to port forwarding, also as application I selected http server. I tried from another PC from same network to go to and it loaded my webserver. But port checker still says port 80 is closed.

I am not sure how to add port to listing and auto config at bottom

Also when I type my external ip in browser with port 80 it loads my router configuration, and before when ports were open and working it loaded only page with error for me, but others was able to connect.

I added port 8081 to port forwarding also, and added to apache config to listen for it, and port is closed also, and browser displays error that page is not available.

I am still looking for solution, thanks for your help guys so far

Have you tried opening your browser (on the computer with IP, typing in to see what happens?
You should also try http://localhost. If the latter works, but not the address, then the apache server most probably have been configured to listen only to the localhost interface.
This means that there might be some Wamp service configuration you can do, or you can try to find the apache config file, and fix it there.

typing or localhost in browser opens my webserver, also from other pc in house going to also opens my webserver,

this is apache config, and I have dynamic external ip so I must give to other people always my ip when it changes

ServerName localhost:80

Listen [::0]:80
Listen 8081

How about this.... lets eliminate everything having to do with either the host or the network.

Shut down the host.

Try to hit the web page from outside your network.

What do you get?

If you see a reply, then its the router answering or another host answering. (check for router services or dupe IPs on the internal network).

If you don't get a reply, then there is a service on the host that is answering using apache and you have port contention.

I sent my external ip to my friend with port 80, and webserver closed

error he gets is

This page is not available

and details

Google Chrome could not load the webpage because took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection.

Have your verified your external IP by going to whatismyipaddress.com from any of your systems and confirming your address. Also be aware that some home ISP's (non-business customers) block port 80 access from the internet. That way you have to buy a business account.

"Google Chrome could not load the webpage because took too long to respond."
That sounds more like a loop.

You should block your public IPs when posting (better safe than sorry).

With that, we are now certain it is not the router, network, or other host.

So now we concentrate on your web server. Like I said, there is something else listening on port 80.

This is a windows box so from command line run 'netstat -anb' . Look for LISTENING on x.x.x.x:80. Underneath the entry, you will see the service that has bound the port.

What do you get?

I have dynamic ip, so no problem in sharing one with you guys, its just exmple of my friends error when try to connect to it

I tried not only port 80 but several others, day before I had these problems it worked all good, with same setup and port etc, I did not changed anything but ports were closed,

for netstat -anb I get this

many other ports and port 80 is

TCP [::]:80 [::]:0 LISTENING

Can not obtain ownership information
TCP [::]:8081 [::]:0 LISTENING

Does [chrome] appear above or below the TCP 80 LISTENTING? In the output, the service appears after the listening port.

oh its above, the real service is httpd.exe then

OK, httpd. So next up would be, lets have a look at your apache conf files. httpd.conf, apache2.conf, any enabled-sites conf files, etc....

this is whole httdp config file

# This is the main Apache HTTP server configuration file.  It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see 
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do.  They're here only as hints or reminders.  If you are unsure
# consult the online docs. You have been warned.  
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path.  If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log" 
# will be interpreted as '/logs/access_log'.
# NOTE: Where filenames are specified, you must use forward slashes
# instead of backslashes (e.g., "c:/apache" instead of "c:\apache").
# If a drive letter is omitted, the drive on which httpd.exe is located
# will be used by default.  It is recommended that you always supply
# an explicit drive letter in absolute paths to avoid confusion.
ServerSignature On
ServerTokens Full

# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path.  If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used.  If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
ServerRoot "D:/Programs/wamp/bin/apache/apache2.4.9"

Define APACHE24 Apache2.4

# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
# Mutex default:logs

# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to 
# prevent Apache from glomming onto all bound IP addresses.
Listen [::0]:80
Listen 8081

# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule actions_module modules/mod_actions.so
LoadModule alias_module modules/mod_alias.so
LoadModule allowmethods_module modules/mod_allowmethods.so
LoadModule asis_module modules/mod_asis.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
LoadModule authn_core_module modules/mod_authn_core.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_socache_module modules/mod_authn_socache.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_host_module modules/mod_authz_host.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
LoadModule authz_user_module modules/mod_authz_user.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule buffer_module modules/mod_buffer.so
LoadModule cache_module modules/mod_cache.so
LoadModule cache_disk_module modules/mod_cache_disk.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
LoadModule cgi_module modules/mod_cgi.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule data_module modules/mod_data.so
#LoadModule dav_module modules/mod_dav.so
#LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule dbd_module modules/mod_dbd.so
LoadModule deflate_module modules/mod_deflate.so
LoadModule dir_module modules/mod_dir.so
#LoadModule dumpio_module modules/mod_dumpio.so
LoadModule env_module modules/mod_env.so
#LoadModule expires_module modules/mod_expires.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
LoadModule file_cache_module modules/mod_file_cache.so
#LoadModule filter_module modules/mod_filter.so
#LoadModule headers_module modules/mod_headers.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule imagemap_module modules/mod_imagemap.so
LoadModule include_module modules/mod_include.so
#LoadModule info_module modules/mod_info.so
LoadModule isapi_module modules/mod_isapi.so
#LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
#LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
#LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
#LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
#LoadModule ldap_module modules/mod_ldap.so
#LoadModule logio_module modules/mod_logio.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule lua_module modules/mod_lua.so
LoadModule mime_module modules/mod_mime.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
LoadModule negotiation_module modules/mod_negotiation.so
#LoadModule proxy_module modules/mod_proxy.so
#LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
#LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
#LoadModule proxy_connect_module modules/mod_proxy_connect.so
#LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
#LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
#LoadModule proxy_http_module modules/mod_proxy_http.so
#LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule remoteip_module modules/mod_remoteip.so
#LoadModule request_module modules/mod_request.so
#LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule rewrite_module modules/mod_rewrite.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule setenvif_module modules/mod_setenvif.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
#LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule speling_module modules/mod_speling.so
#LoadModule ssl_module modules/mod_ssl.so
#LoadModule status_module modules/mod_status.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule unique_id_module modules/mod_unique_id.so
#LoadModule userdir_module modules/mod_userdir.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule version_module modules/mod_version.so
LoadModule vhost_alias_module modules/mod_vhost_alias.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule xml2enc_module modules/mod_xml2enc.so

LoadModule php5_module "D:/Programs/wamp/bin/php/php5.5.12/php5apache2_4.dll"
#PHPIniDir D:/Programs/wamp/bin/php/php5.5.12

<IfModule unixd_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.  
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User daemon
Group daemon


# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition.  These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.

# ServerAdmin: Your address, where problems with the server should be
# e-mailed.  This address appears on some server-generated pages, such
# as error documents.  e.g. admin@your-domain.com
ServerAdmin admin@example.com

# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
ServerName localhost:80

HostnameLookups Off

# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "D:/Programs/wamp/www/"

# Each directory to which Apache has access can be configured with respect
# to which services and features are allowed and/or disabled in that
# directory (and its subdirectories). 
# First, we configure the "default" to be a very restrictive set of 
# features.  
<Directory />
    AllowOverride none
    Require all denied

# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.

<Directory "D:/Programs/wamp/www/">
    # Possible values for the Options directive are "None", "All",
    # or any combination of:
    #   Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
    # Note that "MultiViews" must be named *explicitly* --- "Options All"
    # doesn't give it to you.
    # The Options directive is both complicated and important.  Please see
    # http://httpd.apache.org/docs/2.4/mod/core.html#options
    # for more information.
    Options Indexes FollowSymLinks

    # AllowOverride controls what directives may be placed in .htaccess files.
    # It can be "All", "None", or any combination of the keywords:
    #   AllowOverride FileInfo AuthConfig Limit
    AllowOverride all

    # Controls who can get stuff from this server.

#   onlineoffline tag - don't remove
    Require all granted

# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
    DirectoryIndex index.php index.php3 index.html index.htm

# The following lines prevent .htaccess and .htpasswd files from being 
# viewed by Web clients. 
<Files ".ht*">
    Require all denied

# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here.  If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
#ErrorLog "logs/error.log"
ErrorLog "D:/Programs/wamp/logs/apache_error.log"

# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn

<IfModule log_config_module>
    # The following directives define some format nicknames for use with
    # a CustomLog directive (see below).
    LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
    LogFormat "%h %l %u %t \"%r\" %>s %b" common

    <IfModule logio_module>
      # You need to enable mod_logio.c to use %I and %O
      LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio

    # The location and format of the access logfile (Common Logfile Format).
    # If you do not define any access logfiles within a <VirtualHost>
    # container, they will be logged here.  Contrariwise, if you *do*
    # define per-<VirtualHost> access logfiles, transactions will be
    # logged therein and *not* in this file.
    CustomLog "D:/Programs/wamp/logs/access.log" common

    # If you prefer a logfile with access, agent, and referer information
    # (Combined Logfile Format) you can use the following directive.
    #CustomLog "logs/access.log" combined

<IfModule alias_module>
    # Redirect: Allows you to tell clients about documents that used to 
    # exist in your server's namespace, but do not anymore. The client 
    # will make a new request for the document at its new location.
    # Example:
    # Redirect permanent /foo http://www.example.com/bar

    # Alias: Maps web paths into filesystem paths and is used to
    # access content that does not live under the DocumentRoot.
    # Example:
    # Alias /webpath /full/filesystem/path
    # If you include a trailing / on /webpath then the server will
    # require it to be present in the URL.  You will also likely
    # need to provide a <Directory> section to allow access to
    # the filesystem path.

    # ScriptAlias: This controls which directories contain server scripts. 
    # ScriptAliases are essentially the same as Aliases, except that
    # documents in the target directory are treated as applications and
    # run by the server when requested rather than as documents sent to the
    # client.  The same rules about trailing "/" apply to ScriptAlias
    # directives as to Alias.
    ScriptAlias /cgi-bin/ "D:/Programs/wamp/bin/apache/apache2.4.9/cgi-bin/"


<IfModule cgid_module>
    # ScriptSock: On threaded servers, designate the path to the UNIX
    # socket used to communicate with the CGI daemon of mod_cgid.
    #Scriptsock cgisock

# "D:/Programs/wamp/bin/apache/apache2.4.9/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "D:/Programs/wamp/bin/apache/apache2.4.9/cgi-bin">
    AllowOverride None
    Options None
    Require all granted

<IfModule mime_module>
    # TypesConfig points to the file containing the list of mappings from
    # filename extension to MIME-type.
    TypesConfig conf/mime.types

    # AddType allows you to add to or override the MIME configuration
    # file specified in TypesConfig for specific file types.
    #AddType application/x-gzip .tgz
    # AddEncoding allows you to have certain browsers uncompress
    # information on the fly. Note: Not all browsers support this.
    AddEncoding x-compress .Z
    AddEncoding x-gzip .gz .tgz
    # If the AddEncoding directives above are commented-out, then you
    # probably should define those extensions to indicate media types:
    AddType application/x-compress .Z
    AddType application/x-gzip .gz .tgz
    AddType application/x-httpd-php .php
    AddType application/x-httpd-php .php3

    # AddHandler allows you to map certain file extensions to "handlers":
    # actions unrelated to filetype. These can be either built into the server
    # or added with the Action directive (see below)
    # To use CGI scripts outside of ScriptAliased directories:
    # (You will also need to add "ExecCGI" to the "Options" directive.)
    #AddHandler cgi-script .cgi

    # For type maps (negotiated resources):
    #AddHandler type-map var

    # Filters allow you to process content before it is sent to the client.
    # To parse .shtml files for server-side includes (SSI):
    # (You will also need to add "Includes" to the "Options" directive.)
    #AddType text/html .shtml
    #AddOutputFilter INCLUDES .shtml

# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type.  The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic

# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html

# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited

# EnableMMAP and EnableSendfile: On systems that support it, 
# memory-mapping or the sendfile syscall may be used to deliver
# files.  This usually improves server performance, but must
# be turned off when serving from networked-mounted 
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#EnableMMAP off
EnableSendfile off

# AcceptFilter: On Windows, none uses accept() rather than AcceptEx() and
# will not recycle sockets between connections. This is useful for network
# adapters with broken driver support, as well as some virtual network
# providers such as vpn drivers, or spam, virus or spyware filters.
AcceptFilter http none
AcceptFilter https none

# Supplemental configuration
# The configuration files in the conf/extra/ directory can be 
# included to add extra features or to modify the default configuration of 
# the server, or you may simply copy their contents here and change as 
# necessary.

# Server-pool management (MPM specific)
#Include conf/extra/httpd-mpm.conf

# Multi-language error messages
#Include conf/extra/httpd-multilang-errordoc.conf

# Fancy directory listings
Include conf/extra/httpd-autoindex.conf

# Language settings
#Include conf/extra/httpd-languages.conf

# User home directories
#Include conf/extra/httpd-userdir.conf

# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf

# Virtual hosts
#Include conf/extra/httpd-vhosts.conf

# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf

# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf

# Various default settings
#Include conf/extra/httpd-default.conf

# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf

# Secure (SSL/TLS) connections
#Include conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
#       starting without SSL on platforms with no /dev/random equivalent
#       but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
# uncomment out the below to deal with user agents that deliberately
# violate open standards by misusing DNT (DNT *must* be a specific
# end-user choice)
#<IfModule setenvif_module>
#BrowserMatch "MSIE 10.0;" bad_DNT
#<IfModule headers_module>
#RequestHeader unset DNT env=bad_DNT

#IncludeOptional "D:/Programs/wamp/vhosts/*"
Include "D:/Programs/wamp/alias/*"

Lines 62 and 63 show the listening on all IPs on port 80. Then you have another include on line 556. In that directory, do you have any additional conf files?

I have all files that wamp installs, I did not made any custom, I only added port 8081 to listen also and thats it. I have other conf files for php and mysql etc, just tell me and I can post, but I am not sure that is related to opening port

Be a part of the DaniWeb community

We're a friendly, industry-focused community of 1.20 million developers, IT pros, digital marketers, and technology enthusiasts learning and sharing knowledge.