7,529 Posted Topics

Member Avatar for jellybeans8215

you might want to use Everest ,it will tell you what network adapter it has ,when you run the program just go to networking on the right pain and it will tell you what network adapters name is ,post it here or search the net for drivers when you get …

Member Avatar for abtec
0
211
Member Avatar for rbuskill

It would still be a good idea to go to the hijackthis fourm and post you latest hijack file and get everything removed . [url]http://forums.spywareinfo.com/index.php?showforum=11[/url]

Member Avatar for achatchski
1
511
Member Avatar for anjaj

go into the properties of the video card and check the refresh rate.as it may have changed ,not sure what the laptop should be, but i think its should be 75,hooking it to the projector may have changed it to 60 or so,i have seen blurry laptop screens when set …

Member Avatar for anjaj
0
96
Member Avatar for comp12345

[QUOTE=comp12345;485231]can u tell me more y u not recomemed is it becuz its not good enough or somthing esl wat about this model GA-945GMF will this one support dual core cpu heres the link for both motherboards 945GMF=http://www.gigabyte.co.nz/Products/Motherboard/Products_Overview.aspx?ProductID=1910 8I945P Pro=http://www.gigabyte.co.nz/Products/Motherboard/Products_Overview.aspx?ProductID=1905[/QUOTE] in the links you provide ,just to the right of …

Member Avatar for comp12345
0
106
Member Avatar for Flashdance

[QUOTE=Flashdance;480246]Hello, I (it also wouldn't allow me to safely remove the device because it kept saying it was in use even though everything had finished copying). .[/QUOTE] when this happens i always go to start, and log off user and then log back in ,you will then be able to …

Member Avatar for TheNNS
0
149
Member Avatar for tazsnoop

you will need a WinMe disk to do it ,unless Compaq put a recover partition of the harddrive that will rung by hitting f10 or 11 or something like that ,usually you are greeted with a hit f10 to run recovery at startup if there is one .

Member Avatar for explodinghead75
0
89
Member Avatar for explodinghead75

i read thin and all i can think is ,quick launch ,the fact it gray means nothing ,everything pops up of course it does ,icons for all the program he install and didn't uncheck when asked if he wanted to install a shortcut in start programs and quick launch

Member Avatar for explodinghead75
0
104
Member Avatar for ingeborgdot@yah

if you put the sound card into a different pci slot than it was in before the move you would get this ,but then again if you did do this your sound would not work .does you sound drive show in device manager ,if no then you need to reinstall …

Member Avatar for caperjack
0
95
Member Avatar for chocolate_sala

question ,the ram you are looking at is ddr2,does your motherboard take ddr2 ram or does it take ddr sdram

Member Avatar for ashikkalam123
0
124
Member Avatar for bubbles35
Member Avatar for Orangefeet
Member Avatar for bh99mh

Read through these you should find the answer . ,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, This info was found on [url]http://www.uktsupport.co.uk/epson/Inkjet/sc400.htm[/url] If you see conflict error messages or printing is very slow, the problem may be caused by temporary files in the EPSON Spool Manager temporary file directory. To change the Spool Manager settings, you …

Member Avatar for alexr
0
168
Member Avatar for maddy007

[QUOTE=maddy007;475047]recently i've downloaded a software named "MPlayer-dev-SVN-latest" frm a site......and i dont knw whether it was an approved site or not.....but when it completed downloading there was no option for RUN ....so it asked me for 2 options ...like using appropriate web service/select program frm a list. can anyone help …

Member Avatar for Suspishio
0
195
Member Avatar for milesofjazz

Time to take it to computer shop!!!you don't know hotwto remove the fan you don't know how to lubricate it ,you don't know what kind to buy ,can i as do you fix you own car .

Member Avatar for caperjack
0
99
Member Avatar for woody780

how about some computer specs,cpu speed,amount of ram ,harddrive size and stuff like that . also use ccleaner to remove temp files and do a registry clean. [url]http://www.filehippo.com/download/91d3b585c87e9a61236a9f922b94aadb/download/[/url]

Member Avatar for caperjack
0
130
Member Avatar for rmsmx

its still in the last log you posted O4 - HKCU\..\Run: [LDM] C:\Program Files\Logitech\Desktop Messenger\8876480\Program\BackWeb-8876480.exe

Member Avatar for redtopca
0
339
Member Avatar for variedd

check here . [url]http://msn-errors.blogspot.com/2007/02/fix-8004888d-error.html[/url]

Member Avatar for caperjack
0
112
Member Avatar for 35mm

when i have problems with connecting as you do i run a repair tool correct invalid setting that another program may have set i use this safe program to restore the default settings . [url]http://www.softpedia.com/get/Tweak/Network-Tweak/WinSockFix.shtml[/url]

Member Avatar for caperjack
0
117
Member Avatar for aaassdzzzxxc

the board takes 8x avp. and if i were you i would add at least another 512 meg of ram to the system 1 gig if you can afford it and i can't find it anywhere that video card that say they are 512 meg are really only 256meg ,but …

Member Avatar for jbennet
0
122
Member Avatar for ceslyn
Member Avatar for caperjack
0
104
Member Avatar for curtisg43228

[QUOTE=curtisg43228;472856]I have a T6420 E Machines that powers up, but doesn't boot the keyboard/mouse is not reading. Plus the machine seems to be making a different noise than it normally did (sounds louder). Is this the motherboard or the processor. And what is an affordable alternative to put into the …

Member Avatar for curtisg43228
0
111
Member Avatar for dlawson1986

open computer case .lay it flat on its side ,turn it on, hover you head all around listing with you best ear into the open case ,and you should be able to pinpoint the whistle

Member Avatar for jbennet
0
82
Member Avatar for pphipps

try booting to your win2ooo cd and do a repair ,when you get to the prompt ,type in CHKDSK /r see if it helps fix the problem ,if not post back .

Member Avatar for pphipps
0
93
Member Avatar for harpingheather

i use much caution ,but use all 3,air, soft bristle paint brush,and vacuum,note vacuum only for lower case and front cover and such

Member Avatar for caperjack
0
146
Member Avatar for iceman1007

if the motherboard just stopped working for no apparent reason like a power serge ,the ram should be fine .

Member Avatar for caperjack
0
54
Member Avatar for JAJansenJr

[QUOTE=JAJansenJr;471550]Computer is a Pentium IV 1.3GHz 384 Meg RDRAM. Hard drive is 60 Gig. Has anyone tried all solid state flash drives as their main hard drive? The old slow hard drive has to be part of the problem. Processes show more than 2 pages - best way to share …

Member Avatar for TheNNS
0
1K
Member Avatar for jkatash

hello, i know everyone get in here from a different direction and you my have missed the virus /spyware section i'm going to direct you to but that where the virus/spyware experts hang out, and you will be better served there good luck . [url]http://www.daniweb.com/forums/forum64.html[/url]

Member Avatar for caperjack
0
528
Member Avatar for Faverdi
Member Avatar for mIzDa_cHuBz
Member Avatar for mIzDa_cHuBz
0
56
Member Avatar for zandiago

not likely ,if it wants to continue with setup then he went as far as formating the drive, and there will be no windows installed to boot to anymore .

Member Avatar for zandiago
0
87
Member Avatar for beebel

hello,you need to remove the hdd and connect it to another computer via USB external hdd device ,to remove you data and stuff. .

Member Avatar for bobbyraw
0
100
Member Avatar for iceman1007

read you other post with the problem you are having ,read this . [url]http://support.microsoft.com/kb/307654[/url]

Member Avatar for caperjack
0
85
Member Avatar for mattman51

First thing i would try is to unplug power cord ,hold power on button in for about 30 seconds.then plug it back into power outlet and try turning it on again . if nothing happens,I would then try to reset the Bios to default settings . those are the 2 …

Member Avatar for sureshsigera
0
145
Member Avatar for lastmo
Member Avatar for seneye

[QUOTE=seneye;477545] But my question is. Could I Just add another Graphic card in for another monitor?[/QUOTE] yes ,do a google search on installing 3rd monitor

Member Avatar for seneye
0
157
Member Avatar for sharonis

[QUOTE=sharonis;476480]Do you have any suggetions as how i can get them off the panel (This panel is the one where it shows all your booting info)[/QUOTE] If it still shows in the process of the task manger its still running on you computer ! I use hijackthis ,insted of msconfig …

Member Avatar for sharonis
0
118
Member Avatar for eander23

[QUOTE=eander23;478826] I've tried just hitting "copy" and that doesn't help. .[/QUOTE] did you then go to the hdd and hit paste.also you should be able to just drag and drop in windows Explorer

Member Avatar for caperjack
0
102
Member Avatar for ETE

the 2 chips need to of equal size to work in dual mode ,and motherboard and cpu that supports it ,you definitely don't want to throw the 2100 into the mix, even in single channel mode.and the 2 512 and the 1 gig will not work together in ddr mode …

Member Avatar for caperjack
0
83
Member Avatar for ashikkalam123

are you doing a fresh install of winxp or a upgrade from another windows version . i would suggest a format of the hdd and try the install again .also check this . [url]http://support.microsoft.com/kb/311562[/url]

Member Avatar for TheNNS
0
174
Member Avatar for donbunker900

don't used computer with virus scan running in background,could be you and the virus scan tried aces same address in ram at the same time you were using it .

Member Avatar for coolraj003
0
103
Member Avatar for Elizabeth Marie

Are you using IE7 to connect to internet , also if it wireless on new laptops there is usually a button on the laptop that need to be turned on ,in the case of the new Toshiba laptop ,owned by a customers that i have here its located near the …

Member Avatar for ashikkalam123
0
134
Member Avatar for vigneshvh

and is there is a point to this post ,yes there is ,there is indeed ,it is, Make you computer secure it is .as you will see ,is ,is the thing to do to protect the computer you is using right now [url]http://aumha.org/a/quickfix.htm[/url]

Member Avatar for coolraj003
0
284
Member Avatar for seneye
Member Avatar for hughv
0
165
Member Avatar for Lucy12345

try going into safe mode to delete them ,to get there boot computer,then hitting the f8 key until you get the option to choose safe mode

Member Avatar for caperjack
0
50
Member Avatar for dav6

[QUOTE=dav6;478642]When I got the pc the first thing I did was put the XP disc in and set up partitions and installed . Then I used the Bios disc to set up hardware could this be the problem. [/QUOTE] i assume you mean motherboard disk to setup hardware ,as i …

Member Avatar for caperjack
0
85
Member Avatar for phill44

[QUOTE=lhhester;477245]Hey Dude, I'm having the same problem with the hanging windows screen. How do I get to the Autoexe.Bat file to edit it? thanks[/QUOTE] like it said in previous post reboot into safe mode ,do this by hitting the f8 key many times when you start the computer .do a …

Member Avatar for The Dude
0
182
Member Avatar for freeb75

we hear yah,you should mark thread as solved ,solve icon near the bottom of this post somewhere

Member Avatar for caperjack
0
121
Member Avatar for kingessa

you are posting winxp problem in a win98 section ,go the winxp section and give some more details as to how you did the upgrade and such

Member Avatar for caperjack
0
21
Member Avatar for thinkbig

hello and welcome to Daniweb ,you will get better help if you post the hjt file in the spyware forum were the hjt log readers hang out .,good luck . click this link and start a new post there . [url]http://www.daniweb.com/forums/forum64.html[/url]

Member Avatar for thinkbig
0
219
Member Avatar for archon

when booting to winxp cd did you hit f6 to install sata drivers for the hdd,you may have to do this first ! you will find sata drivers on the motherboard cd.but will need a floppy drive and disk to copy them when hitting f6

Member Avatar for bobbyraw
0
107

The End.